: Plastic Bubble Bags Saddlebags for Harley Panhead White Here is a new in the package reproduction set of plastic saddlebags for vintage Panheads. Often called "Bubble Bags" these beauties were used from 1954 to 1962 on rigid and swing arm frames. With the correct brackets they could be run on any factory or factory type rigid frame. With the correct swing arm brackets they could be used up to...
: Front Fork Cover Panel Kit Harley Panhead Rear & Top Here is a new in the package pair of reproduction front fork panels as used on Harley Panheads. These stainless steel covers are the rear and top tree mounted panels as found on Harley Davidson Panhead front forks from 1949 to 1959. This would be correct for Panhead E, EL, F, FL, FLH. For all four pieces (whole kit) or other individual piec...
: Rebuild Kit for Harley Linkert Carb with Bowl Nut Knucklehead ~ Panhead Brass Here is a new in the package reproduction rebuild kit for Harley and Indian brass Linkert carburetors. This kit can be used on any brass bodied carbs from 1933 to 1965. It includes a brass float, lever pin, lever bearing screw, needle and seat, all the gaskets, springs, screws and balls. Also included is the cad pla...
: Primary Case Breather Kit Vintage Harley Panhead Here is a new in the package replica of the primary case breather tube as found on 1958 to 1964 Panheads. This item served a triple purpose. It relieved crankcase pressure, lubed the primary chain and was a motor case stud to keep the engine case together. This kit is sold with a replica primary chain oiler nipple. This nifty little gadget fits...
: Harley Rear Brake Drum '58 to '62 Hydraulic Panhead Here is a used genuine Harley rear brake drum for Harley Panhead. This is the type used on the 1958 to 1962 hydraulic or "juice" brake setup. This is the later style cast drum. The sprocket is worn and should be replaced. The shoe contact area has been turned and is .020" over stock. Otherwise the drum is in good condition. It is black and h...
Similar
: Pinion Shaft Bearing Kit for Harley Big Twin 40-54 Here is a new in package pinion shaft bearing kit for Harley Big Twin Flatheads, Knuckleheads and Panheads. This replica kit includes 12 standard size bearing rollers, the cages, washer and snap ring to replace those on 1940 to 1948 U, UL, ULH 74" and 80". Also included is the right bearing spacer to make this a complete kit for the 1940 to 1...
: Pinion Shaft Bearing Kit for Harley Big Twin 40-54 Here is a new in package pinion shaft bearing kit for Harley Big Twin Flatheads, Knuckleheads and Panheads. This replica kit includes 12 standard size bearing rollers, the cages, washer and snap ring to replace those on 1940 to 1948 U, UL, ULH 74" and 80". Also included is the right bearing spacer to make this a complete kit for the 1940 to 1...
: Pinion Shaft Bearing Kit for Harley Big Twin 40-54 Here is a new in package pinion shaft bearing kit for Harley Big Twin Flatheads, Knuckleheads and Panheads. This replica kit includes 12 standard size bearing rollers, the cages, washer and snap ring to replace those on 1940 to 1948 U, UL, ULH 74" and 80". Also included is the right bearing spacer to make this a complete kit for the 1940 to 1...
: Shifter Shift Gate (Guide) for Harley Big Twin 1947 & 1948 3 speed Here is a new in the package reproduction shifter gate or guide as HD calls it. This item will directly replace the one bolted to '47 to '48 Big Twin Flatheads, Knuckleheads, and Panheads with 3 speed transmissions. Shift pattern is 32N1 front to rear. Some '47 and '48 Big Twin Flatheads, very few Knuckleheads and Panheads cam...